SrMouraSilva · Plugin manual

Gossiper

Know what your controller just did.

Screen and CV feedback for controls that have none of their own, for MOD Dwarf, MOD Duo X and MOD Duo

7 footswitches4 potentiometers11 CV outputs

Gossiper
User manual · November 2026 editionv1.1.21

Gossiper gives you screen and CV feedback for controls that don't have any of their own — typically an external MIDI foot controller or knob box with no LEDs or display.

The Gossiper panel: a display with the last control used, 7 footswitch indicators and 4 potentiometer meters
The Gossiper panel: a display with the last control used, 7 footswitch indicators and 4 potentiometer meters

Assign one of its parameters to receive the MIDI (or CV, or device control), and Gossiper turns that into a plain CV signal and a pop-up notification on the device screen.

It is an "educated gossiper": it only gossips about a control if you're actually looking at it. A pop-up appears only on a device screen page that has one of Gossiper's four pop-up slots linked to a control of it (a knob or a footswitch), because MOD devices only show a pop-up for a plugin whose parameter is linked to a control that is currently visible on the screen. (The settings page calls them Pop-up slot 1–4; the parameters behind them are named Assign to notify 1–4, as MOD UI lists them.)

Good to know

Gossiper has no audio inputs or outputs, so it doesn't sit in your signal chain. Place it anywhere on the pedalboard. The CV outputs, the display on the plugin and the pop-ups are three independent ways of using the same control: you can use any of them, and the outputs keep working when the pop-ups cannot (an old firmware, a MOD Duo).

Sample demonstration of the plugin in action
01

Plugin GUI overview

Gossiper at work: footswitches and potentiometers move from outside, as a MIDI controller would, and the display says which one was used last
Gossiper at work: footswitches and potentiometers move from outside, as a MIDI controller would, and the display says which one was used last
The Gossiper panel 1 2 3 4 5 6
The Gossiper panel: Footswitch 2 was used last and is on, Pot 1 is at 20% and Pot 3 at 63%.
Item Description Interactivity
1Display Says which control was used last and what it did: the name of the footswitch and ON or OFF, or Pot 3 and its percentage. It stays on, and lights up for a moment each time a control is used. This is how you see a message on a device that has no screen for plugin pop-ups, such as the MOD Duo. Only visualization status
2Footswitch indicator A disc in a colour of its own for each footswitch. Lit while the footswitch is ON, and mirrored on its CV jack (0 V / 10 V). The one used last is outlined. Only visualization status. Clicking on it does nothing.
3Footswitch label Click and type a name (up to 15 characters): this is the text the pop-up and the display show for that footswitch. Editable field
4Potentiometer The position of the knob (0–100 %) as a meter, and the CV range (Minimum–Maximum, in volts) its 0–10 V output is scaled into. The one used last is outlined. Only visualization status. To change the range, open the settings.
5Settings Opens the settings page (section 4). The gear icon above the plugin opens it too. Button
6CV outputs 1–7 are the footswitches and P1–P4 the potentiometers. Jacks
02

Interactive manual

Here the plugin is the real one: the same interface, the same script, running inside the manual. Press Open the interactive manual under the picture to open it full screen (Esc or Close brings you back). Nothing you do is saved or sent anywhere, and Reset puts it back the way it starts.

  • Explore: tap any part of the plugin to read what it is for, or pick it from the list under the picture. Show areas outlines everything that can be tapped. Use the buttons at the top to switch between the plugin on the pedalboard and its settings page.
  • Guided tours: step-by-step walkthroughs of the common tasks. A finger shows where to tap. Go forward and back with Next and Back: every step says what is happening and shows it in the plugin.

The box under the plugin is your controller

Gossiper only shows what a control did from outside, so there is nothing to press on the plugin itself. The box drawn under it stands for your MIDI foot controller: press its buttons and turn its knobs, and watch the display, the discs and the CV follow. It is not part of the plugin.

03

What it's for

A MIDI foot controller (say, a cheap "Chocolate"-style box) can send Program Change or CC messages, but usually has no LED to confirm whether a patch is currently on or off, and no screen to show a knob's value. Gossiper closes that loop:

  1. Assign a Footswitch N or Potentiometer N parameter to receive that MIDI message (or a CV signal, or a device knob/footswitch).
  2. Link one of the 4 pop-up slots (Screen pop-ups on the settings page) to a knob or footswitch of the device page you play from.
  3. Use the CV output. CV Foot - Out N (footswitches) or CV Pot - Out N (potentiometers) now carries a plain, calibrated CV signal you can route into any other plugin's CV-addressable parameter — the same way you would with a "Control to CV" utility plugin.

From then on, every time that MIDI controller sends a message, you see it confirmed on the device screen — without needing to look down at an unlit external box.

04

Setting it up on the device

The shortest path

Open the settings page, tap Assign next to Footswitch 1 and press the button of your controller; then tap Assign next to Pop-up slot 1 and pick a knob or footswitch of the page you play from. Press the button again: its name pops up on the device screen, the disc lights up on the plugin and CV Foot - Out 1 goes to 10 V. The steps below show each tap.

Click Settings (or the gear icon above the plugin) to open the settings page. It has one panel for each thing you can link, and each panel starts with Hardware assignment: that is the step where you choose which control of your device, your MIDI foot controller or your pedal drives that parameter.

The settings page
The settings page
Going through the settings page: a footswitch is renamed, and every page is visited with the arrows of the top bar
Going through the settings page: a footswitch is renamed, and every page is visited with the arrows of the top bar

On a small screen the page splits into several pages instead of scrolling: use the arrows in the top bar (they are always there), the dots between them, or swipe sideways on a touch screen.

Step 1 — Assign the control. In Footswitches, find a row that is not used yet — or, in Potentiometers, a row for a knob — and tap Assign next to it.

Step 1: tap Assign next to Footswitch 1
Step 1: tap Assign next to Footswitch 1

In the opened modal, select MIDI option in Assign to.

The assignment dialog of MOD UI: Assign to MIDI
The assignment dialog of MOD UI: Assign to MIDI

Now you must send the MIDI message (or pick the device control) you want to drive it. After it, save. The button shows a check mark once it is assigned.

Step 2 — Assign a pop-up slot. Do the same for one of the four slots in Screen pop-ups — this is what decides where the pop-up will show.

Step 2: tap Pop-up slot 1
Step 2: tap Pop-up slot 1

Step 3 — Choose the target. Pick what the slot is addressed to — usually Device, so it lives on the screen itself.

Step 3: choosing the assignment target
Step 3: choosing the assignment target

Step 4 — Pick the page and control. Choose which page (and which knob or footswitch, B/C) the slot sits on. Whenever that page is showing, that's where the pop-up appears.

Step 4: picking a page, knob or footswitch
Step 4: picking a page, knob or footswitch

Repeat step 1 for as many footswitches/potentiometers as you're feeding in, and steps 2–4 for as many slots as you want pages covered by — up to 4, so you can get a pop-up whichever of up to 4 pages you're currently on.

The page also lets you type the name of each footswitch and the Min and Max voltage of each potentiometer, and keeps your own presets (Saved presets).

Min and Max: the CV range of a potentiometer, in volts
Min and Max: the CV range of a potentiometer, in volts

No screen for pop-ups? The MOD Duo (and any device without the HMI) cannot show pop-ups: the display on the plugin itself (item 1, section 1) is the feedback there. Open the pedalboard and look at it. On the MOD Duo the Screen pop-ups slots of the settings page are disabled, with a note that says why.

05

How the pop-up decides when to appear

Your controllerMIDI foot controller
Gossiperthe plugin on the pedalboard
MOD Dwarfseen from above, and its screen magnified

  • Footswitches gossip immediately — the pop-up is titled Gossiper and shows the footswitch's custom label the instant it flips, styled inverted when turning ON and normal when turning OFF. If two footswitches flip in the very same instant, only the lowest-numbered one gets its pop-up.
  • Potentiometers gossip once you stop — the pop-up is titled Gossiper - Pot N and shows the position, like 63.00%, a short moment after the value settles, so sweeping a knob doesn't spam a message on every intermediate step.
  • No linked slot, no pop-up. If none of the 4 pop-up slots is linked to a control of the page showing on the screen, Gossiper stays silent. The disc, the display and the CV outputs of the plugin do not depend on it.

Requires MOD Dwarf firmware v1.13 or newer for the pop-up mechanism. On older firmware the CV outputs still work; you just won't get the on-screen message.

Note from the author: the pop-up is meant for occasional confirmation, not as a live debugging readout — don't expect to use it for something that changes every few milliseconds.

On the screen of the device

With the aLabs Starless image (Starless 19 or later) the MOD Dwarf and the MOD Duo X can show widgets of a plugin on their screens, drawn by the plugin itself. The stock MOD firmware does not have this: the plugin works the same there and simply shows nothing. On the MOD Duo there is no screen to draw on.

Gossiper's widgets on the MOD Dwarf (left) and on the MOD Duo X (right)
Gossiper's widgets on the MOD Dwarf (left) and on the MOD Duo X (right)

A widget is for looking, not for touching: nothing on the screen reacts to a finger or to a button of the device. What changes it are the controls you assigned to the plugin, as always; the widget follows them.

Placing a widget

  1. Open the Display dialog (the Device menu of MOD UI) and choose one of the two widgets (Footswitches or Potentiometers) in the list of widgets of the pedalboard.
  2. Place it on an area of the screen: a column above a knob, two or three columns, a footer, both footers or the whole screen on the Dwarf; a knob, two knobs, the four knobs, the encoder band, a footer, both footers or the whole screen on each display of the Duo X. The dialog only offers the areas that are big enough for it.
  3. The dialog offers to assign the seven footswitches (for Footswitches) or the four potentiometers (for Potentiometers) to controls of the device; you can change any of them or leave it out.
  4. Save. Each can be placed on more than one area at once (a column and a footer, or one on each display of the Duo X).

Each draws what fits in the area it gets: a footer shows the bare essentials, the whole screen shows everything.

Unlike the pop-up, a widget needs no pop-up slot linked to a control and does not go away: it stays on the screen where you placed it.

Footswitches

Shows which of the seven footswitches are on, as numbered boxes (filled: on), under the name Gossiper where there is room for it. When a footswitch changes, its name and its new state (ON or OFF) appear over the widget for a moment, like a pop-up, and then the boxes come back. It is offered in every area, from a footer up.

MOD Dwarf MOD Duo X What you see
Footswitches on the MOD Dwarf: one footerOne footer · 51 × 10 Footswitches on the MOD Duo X: one footerOne footer · 64 × 8 A row of numbered boxes (filled: on). Only the footswitches assigned to a control of the device (all seven when none is).
Footswitches on the MOD Dwarf: both footersBoth footers · 104 × 10 Footswitches on the MOD Duo X: both footersBoth footers · 128 × 8 The boxes in a row: the assigned ones (seven when none is).
Footswitches on the MOD Dwarf: one columnOne column · 40 × 37 Footswitches on the MOD Duo X: two knobs, one above the otherTwo knobs, one above the other · 64 × 30 Gossiper and the boxes under it, in rows. Only the assigned ones (all seven when none is).
Footswitches on the MOD Dwarf: two columnsTwo columns · 82 × 37 Footswitches on the MOD Duo X: the four knobsThe four knobs · 128 × 30 Gossiper and the boxes in one row: the assigned ones (seven when none is).
Footswitches on the MOD Dwarf: three columnsThree columns · 124 × 37 Footswitches on the MOD Duo X: encoder band and knobsEncoder band and knobs · 128 × 47 The same, with taller boxes.
Footswitches on the MOD Dwarf: whole screenWhole screen · 128 × 64 Footswitches on the MOD Duo X: whole screenWhole screen · 128 × 64 A list of all seven, each with its name and ON or OFF. A footswitch that is not assigned has a dotted box and says UNASSIGNED where the state would be (when none is assigned, all look alike).
No area of this kind Footswitches on the MOD Duo X: one knobOne knob · 64 × 16 A row of numbered boxes. Only the assigned footswitches (all seven when none is).
No area of this kind Footswitches on the MOD Duo X: two knobs side by sideTwo knobs side by side · 128 × 16 The boxes in a row: the assigned ones (seven when none is).

The pop-up fills the area (a footer shows it as one light bar: name on the left, state on the right). Changes in the first second after the plugin loads are not shown, so a pedalboard that comes up with footswitches on does not flash them all.

An area (apart from the whole screen) is not spent on footswitches you do not use: the widget shows only the footswitches that are assigned to a control, in every area. (Until you assign one, it shows all seven.) The names are the ones you gave them (see Renaming a footswitch).

How Gossiper knows which ones are assigned: the device only tells a plugin about its own controls (a footswitch or a knob of the device), not about a MIDI controller, a CC or a CV, so the settings page does it. Every time you assign or unassign a Footswitch N it writes the result into the plugin's hidden Footswitch N in use parameter (footswitch_in_use_1 to footswitch_in_use_7, 1 = in use). They are saved with the pedalboard and are not on the settings page (nobody assigns them). So the widget works the same without a browser open, and you can set them yourself when you control the plugin from an API: with all seven at 0 the widget shows all seven. A footswitch assigned to a control of the device itself counts as in use even with its parameter at 0.

The states of Footswitches
The states of Footswitches

Potentiometers

Shows the four potentiometers (the controls you assigned to Potentiometer 1 – 4) as bars, with the value as a percentage where there is room.

MOD Dwarf MOD Duo X What you see
Potentiometers on the MOD Dwarf: one footerOne footer · 51 × 10 Potentiometers on the MOD Duo X: one footerOne footer · 64 × 8 Four small bars side by side.
Potentiometers on the MOD Dwarf: both footersBoth footers · 104 × 10 Potentiometers on the MOD Duo X: both footersBoth footers · 128 × 8 The same, wider.
Potentiometers on the MOD Dwarf: one columnOne column · 40 × 37 Potentiometers on the MOD Duo X: two knobs, one above the otherTwo knobs, one above the other · 64 × 30 Four upright bars, with their numbers under them.
Potentiometers on the MOD Dwarf: two columnsTwo columns · 82 × 37 Potentiometers on the MOD Duo X: the four knobsThe four knobs · 128 × 30 Dwarf: one row for each, P1 – P4, with a bar and the value in percent. Duo X: four upright bars with their numbers.
Potentiometers on the MOD Dwarf: three columnsThree columns · 124 × 37 Potentiometers on the MOD Duo X: encoder band and knobsEncoder band and knobs · 128 × 47 One row for each, P1 – P4: a bar and the value in percent.
Potentiometers on the MOD Dwarf: whole screenWhole screen · 128 × 64 Potentiometers on the MOD Duo X: whole screenWhole screen · 128 × 64 The same, taller.
No area of this kind Potentiometers on the MOD Duo X: one knobOne knob · 64 × 16 Four upright bars, with their numbers under them.
No area of this kind Potentiometers on the MOD Duo X: two knobs side by sideTwo knobs side by side · 128 × 16 The same, wider.

The value is the position of the knob, from 0 to 100%, not the voltage on the CV output (which also depends on the Minimum and the Maximum).

The states of Potentiometers
The states of Potentiometers
06

Renaming a footswitch

Click a footswitch's label field and type a new name (up to 15 characters). Allowed characters are letters, digits, spaces and + - : _ .; anything else is replaced with _. The name is what the pop-up shows for that footswitch, and it's saved with the pedalboard/preset.

Renaming Footswitch 2 on the pedal
Renaming Footswitch 2 on the pedal
07

Recipes

Each recipe says which Gossiper control your MIDI controller drives, what to type in the settings page and where the CV output goes. Do the steps of section 4 first (assign the control, link a Pop-up slot). Then, on the pedalboard, click Manage CV ports (Pedalboard actions bar of MOD UI) and check the Gossiper outputs you use, so they can be chosen as a CV source. There is no cable to draw: you open the addressing of each parameter you want to control, choose CV and pick the Gossiper output in the list. A potentiometer's voltage is its Min – Max range.

Four-switch controller

Gossiper control Name (type it) CV output →
Footswitch 1 Drive On/Off of the drive
Footswitch 2 Chorus On/Off of the chorus
Footswitch 3 Delay On/Off of the delay
Footswitch 4 Reverb On/Off of the reverb

The classic use. A four-switch controller, like the M-VAVE Chocolate, turns effects on and off, and the device tells you which one just changed, by name. Link Pop-up slot 1 to a control of the page you play from, so the news is always in view.

Setup: controller switches A–D → Footswitch 1–4 (MIDI) · on each effect, address its On/Off to CV and pick CV Foot - Out 1–4.

Expression pedal with a readout

Gossiper control Range CV output →
Pot 1 0 V – 10 V position of a wah, or the volume

A MIDI expression pedal on Pot 1 drives a wah or a volume plugin. When you stop moving the pedal, the device shows where you left it, Gossiper - Pot 1 and 63.00%, which helps when the pedal has no markings. The display on the plugin follows it while you move.

Setup: expression pedal → Pot 1 (MIDI) · on the wah (or the volume), address the knob to CV and pick CV Pot - Out 1.

Safe-range sweep

Gossiper control Range CV output →
Pot 2 3 V – 7 V feedback of a delay

The whole sweep of the pedal now covers only the middle of the target knob (30% to 70% of a 0–10 V range), so you can stomp it all the way down without the delay running away into endless feedback. Set Min to 3 and Max to 7 on the settings page, and adjust them until the extremes sound right (see Tame the range of a knob, section 8).

Setup: second pedal or knob → Pot 2 (MIDI) · on the delay, address the feedback knob to CV and pick CV Pot - Out 2.

One plugin instead of many

Gossiper control Replaces
Footswitch 1–7 Seven on/off "Control to CV" plugins
Pot 1–4 Four continuous "Control to CV" plugins

If your pedalboard uses many "Control to CV" plugins to turn MIDI into CV, move them into one Gossiper: it does the job of all of them, at a fraction of the CPU cost, and you get the pop-ups and the display for free. For instance, a forum user reported that, after replacing those plugins with Gossiper, the Dwarf's CPU usage went down from 81% to 72%.

Setup: re-address each MIDI mapping to a Gossiper footswitch or pot · on each parameter that was controlled by a "Control to CV" plugin, change its CV addressing to the matching Gossiper output.

08

Tips

Name the footswitches after what they do

The pop-up shows the label, so Drive or Solo says more on a screen than Footswitch 3. Rename them before you assign the controller, and you will recognise the message without counting buttons.

One pop-up slot per page you play from

A pop-up shows only while the control you linked to a slot is visible. If you play from two pages of the device, link a second slot to a control on the other page, and so on up to four.

Footswitch and CV in one go

A footswitch that Gossiper receives is also CV Foot - Out N (0 V off, 10 V on). Address a plugin's On/Off to that output and a MIDI button turns the plugin on, with the name on the screen. The feedback and the action come from the same control.

Tame the range of a knob

A potentiometer reaches its CV output scaled into Minimum–Maximum volts. Set Minimum 2 to 2 V and Maximum 2 to 6 V and the whole sweep of the knob moves a parameter between 20 % and 60 % of a 0–10 V range, without losing resolution on the knob.

Do not use it as a meter

The pop-up of a potentiometer waits for the value to settle, so it is for confirming a position, not for watching a value change continuously. Use the display on the plugin for that.

09

Questions & answers

I move my controller but no pop-up appears.

Check, in this order:

  1. The control that sends the message is linked to a Footswitch N or Pot N parameter (the Assign tile of its row on the settings page shows a check mark).
  2. One of the four pop-up slots (Screen pop-ups on the settings page) is linked to a control of the device: a knob or a footswitch.
  3. That control is visible on the screen right now. It is the page the device is showing; on another page, Gossiper stays silent (see section 5).
  4. The device is a MOD Dwarf with firmware v1.13 or newer.
  5. For a potentiometer, you stopped moving it: its pop-up comes a moment after the value settles, not during the sweep.

The disc and the display on the plugin and the CV outputs work without any of these. If they react, only the pop-up setup is missing.

I move my controller but the plugin I want to control does not react.

The parameter you want to control has to be addressed to CV. Click Manage CV ports on the Pedalboard actions bar and check the Gossiper outputs you use, then open the addressing of the On/Off parameter (or the knob), choose CV and pick the matching Gossiper output in the list (CV Foot - Out N / CV Output N for a footswitch, CV Pot - Out N for a potentiometer). There is no cable to draw. Also check that your controller is MIDI-learned to the right Gossiper row: the Assign tile of Footswitch N on the settings page has a check mark when it is.

I press the pop-up slot control on my device and nothing happens.

That is by design. The pop-up slots (the parameters Assign to notify 1–4) are placeholders: they only give Gossiper a control of the device to show its messages on. They do not switch anything.

The settings page says "Pop-up slot" and I also see "Assign to notify". Is it the same?

Yes. The settings page names the four tiles Pop-up slot 1–4, in the panel Screen pop-ups. The parameter behind each one is Assign to notify N, which is the name MOD UI lists in its own assignment dialog and the port reference of this manual uses. A Footswitch N row is the parameter Footswitch N, and a Potentiometer row is Pot N; the Min and Max fields are Minimum N and Maximum N.

How many pages can show a pop-up?

As many as you link slots: one slot for each page you play from, up to four. A slot is linked to one control; if two pages need it, use two slots.

Does it work on the MOD Duo and the MOD Duo X?

The plugin loads and the CV outputs work on both. The MOD Duo has no screen for plugin pop-ups, so the display on the plugin (open the pedalboard in the browser) is where you see the last control used, and the Screen pop-ups slots of the settings page are disabled there. Pop-ups need the HMI of the Dwarf. The Dwarf and the Duo X can also show Gossiper as a widget that stays on the screen (see On the screen of the device, in section 5).

Can I have it on the screen all the time instead of a pop-up?

Yes, with the display widgets: Footswitches shows which of the seven are on, and Potentiometers shows the four bars. They need the aLabs Starless image (Starless 19 or later), and no pop-up slot. On the stock firmware there are no widgets: the plugin works the same, without them.

Does it process audio? Is it stereo? Does it add latency?

No to all three: Gossiper has no audio ports. It only reads its parameters and sends control voltages, so you can put it anywhere on the pedalboard.

Can I control the same effect from a device footswitch and from my MIDI controller?

Not directly: a parameter can only have one addressing. A workaround shared on the forum is to send both signals as CV to a CV logic plugin set to XOR, and connect its output to the effect.

Can the potentiometer pop-up show a custom name?

No. Custom names are for footswitches. The pop-up of a potentiometer is always Gossiper - Pot N with the position of the knob, from 0 to 100% (not the voltage, which also depends on Min and Max).

Why does the potentiometer pop-up appear late?

Gossiper waits until the value stops changing for a short moment, so a sweep of a knob gives one message at the end instead of dozens on the way. For the same reason the pop-up is for confirming a position, not for watching a value change: use the display on the plugin for that.

I changed two footswitches at the same time and only one pop-up appeared.

If two footswitches flip in the very same instant, Gossiper shows the pop-up of the lowest-numbered one. The disc, the display and the CV output of each one still follow.

Why do some characters in my label turn into "_"?

A name accepts letters, digits, spaces and + - : _ . only, up to 15 characters. Anything else is replaced with an underscore.

Are the names saved?

Yes. The name of each footswitch is saved with the pedalboard and with the plugin presets.

Can I invert a knob with Min and Max?

No. The two values are put in order, so a Min of 8 V and a Max of 2 V give the same range as 2 V and 8 V. To invert a control, use a plugin that does it on the CV.

Why can't I turn the footswitch indicator on by clicking it?

The disc only shows what the footswitch received. Gossiper reports on a control that lives elsewhere; to change it, use the controller, or the parameter in the plugin's own addressing.

10

Port reference

Port Type Description
CV Foot - Out 1–4, CV Output 5–7 CV output 0 V / 10 V, mirrors Footswitch N (the first four have the longer name).
Footswitch 1–7 Control input (toggle) Assign this to receive MIDI/CV/device input.
Assign to notify 1–4 Control input The Pop-up slot 1–4 of the settings page. No audio/CV effect; link it to a control of a device page so pop-ups show there.
Pot 1–4 Control input (0–1) Assign this to receive MIDI/CV/device input.
Minimum N / Maximum N Control input (volts) The CV range Potentiometer N's 0–1 value is scaled into.
CV Pot - Out 1–4 CV output Potentiometer N scaled into [Minimum N, Maximum N] volts.
Footswitch label 1–7 Plugin property (patch) The custom name for each footswitch, edited from the GUI text field.
11

Specifications

Field Value
Plugin name Gossiper
Version 1.1.21 (the version of the plugin this manual is for)
Category Control Voltage · Utility
Format LV2 · URI http://srmourasilva.github.io/plugins/gossiper
Audio I/O None
CV outputs 7 × footswitch (0 V off / 10 V on) · 4 × potentiometer (scaled into Minimum–Maximum, 0–10 V)
MIDI None (the controller's messages arrive through the device's assignment)
Assignable parameters Footswitch 1–7 (toggle) · Pot 1–4 · Minimum / Maximum 1–4 · Assign to notify 1–4 (the pop-up slots)
Device feedback Pop-up notifications (MOD HMI, Dwarf firmware v1.13 or newer) · display and indicators on the plugin
Additional features Display widgets with the Starless HMI Widget Extensions (MOD Dwarf and Duo X)
Platforms MOD Dwarf · MOD Duo X · MOD Duo
Developer Paulo Mateus (SrMouraSilva)
License Apache-2.0
Source code github.com/SrMouraSilva/plugins-lv2
Store page Gossiper
Forum thread forum.mod.audio – Gossiper

Gossiper is a community plugin. Feedback, bug reports and pull requests are welcome in the forum thread and on GitHub.